Need Answers Now?
Call 262-820-2400.



Bevco Engineering Company, Inc.
W222N5739 Miller Way
Sussex, WI 53089
Ph. 262-820-2400
Fax 262-820-2599



For all your material handling needs visit Babush Material Handling Systems, Inc.

Fiberglass Shelter: Model 7521-F
  
Applications
Chemical Storage
Chorination Equipment
Monitoring Equipment
Generators
Pumps
Lift Stations
Field Instruments
Electronic Equipment
Pollution Control/Monitoring Equipment
  
Standard Equipment
One exhaust fan providing complete air change every minute
Automatic-manual selector switch, externally mounted and interlocked for automatic operation of the exhaust fan and light when door is opened
Plastic bulkhead fittings for chlorination vent and vacuum lines
Door actuated microswitch for fan and light
Main electrical panel provided on the wall with the following equipment wired and mounted on the panel
Safety switch, 2 pole fused for 30 amps, 120 volt 60 cycle, single phase
Duplex electrical receptacle
PVC light fixture(s) with covered bulb
Heater, with thermostat appropriately sized for each house
 Features
Gas tight gasketed doors
Gas tight observation window on door 
One intake louver for ventilation with bug screens
Three point latch with key lock
Fire retarding insulation on all sides
Electrical power inlet connector (LB Fitting)
Pitched roof to withstand 30 lbs./sq. ft. snow load with drip lip
Vinyl covered floor
Large subpanel with extra space for field mounting of accessories
  
Options Available
Any non-standard power supply
Mounting, wiring, and piping of any type of equipment needed
Motor starters, magnetic or manual
Circuit breaker lighting distribution panels
High temperature safety override
Fan canopy
Special color
Special holes or plumbing connections
Alarm lights, horns, and silencing equipment
Timer for exhaust fan
Exterior lighting

Get a Quote

Download the AutoCAD drawing.
Click Here

AutoCAD® version 14 or later is required to open the files from this site.

SPECIFICATIONS

1.0 SCOPE - This specification describes a Bevco House as manufactured by Bevco Engineering Company, Inc., W222N5739 Miller Way, Sussex, WI 53089. 

2.0 DESCRIPTION - The house shall be completely assembled, ready to install, and capable of housing any equipment as shown on the drawings. The Bevco House shall be model 7521-F and shall be supplied with all components factory mounted and wired. 

3.0 DESIGN - The house shall be of a one piece molded fiberglass reinforced (FRP). The floor shall be 11 gauge steel provided as an integral part of the house and reinforced to support gas cylinders or other heavy objects. The floor shall be vinyl covered. The interior of the house shall be insulated with a 1" minimum layer of plastic insulation. The plastic insulation shall meet U.L. specifications for fire resistant SE-1 foam with an R-value of 7.2. The house shall have dimensions of 54" wide, 24" deep, by 72" high with predrilled holes for fastening to 1/2 inch bolts preset in concrete. The roof shall be pitched and provided with a drip lip. The side wall shall contain two screened vents, one for an air inlet and one for exhaust. The house shall have two independent continuously hinged, three point latched doors. One door shall have a key lock handle. A gastight window, 9"x7", shall be provided for inspection of the interior without opening the door. 

4.0 COMPONENTS - The house shall have the following components factory mounted and wired in non-conductive, non-corrosive electrical conduit boxes and fittings. 

4.1 ELECTRICAL FIXTURES - The following electrical fixtures shall be provided: PVC light fixture with covered bulb. Exterior mounted weatherproof automatic-manual selector switch interlocked with a door actuated micro switch to operate the fan and lights either manually or automatically when the door is opened. A 2 pole 120/60/1, fused safety switch of sufficient size to handle the electrical accessories. Duplex receptacle(s) in PVC weatherproof enclosure. 

4.2 EXHAUST FAN AND INTAKE LOUVERS - An exhaust fan shall be provided with intake louvers capable of providing complete air change every minute. 

4.3 HEATER AND THERMOSTAT - A heater and thermostat with sealed contacts of sufficient size shall be provided. 

4.4 MISCELLANEOUS - Plastic vent and vacuum bulkhead fittings will be supplied.

 

Model ECS-F  |  Model 7521-F  |  Model 7521-S
Model 7523-F  |  Model 7523-S  |  Model PBF | Clamshell

copyright ©2002-2006 Bevco Engineering Company, Inc.